Ogólnopolskie forum modelarzy FSR
http://www.fsrv.wroclaw.pl/forum/

Śruby Ściągawka jak dobierać Sruby OCTURA
http://www.fsrv.wroclaw.pl/forum/viewtopic.php?f=2&t=1911		 Strona 1 z 1
Autor:  AndrzejC [ 22 lut 2012, 18:22 ]
Tytuł:  Śruby Ściągawka jak dobierać Sruby OCTURA
Znalazłem na jakiejś stronie zakupowej taką tabelę śrub firmy OCTURA.
Myślę ,że to może się przydać przy zakupie i doborze śrub do łodek.

BASIC PROPELLER RECOMMENDATIONS
DEEPVEE - INBOARD - SUBMERGED PROP
3.5 cc - 1337/3, 1640, 1938, X438,456
DEEPVEE - INBOARD - SUBMERGED PROP

7.5 cc - X445, X447, X645, X646
DEEPVEE - INBOARD - SUBMERGED PROP

11 cc - X447/3, X448, X452, X646/3, X648, X548
DEEPVEE - INBOARD - SUBMERGED PROP

15 cc - X455, X455/3, X457, X457/3
DEEPVEE - INBOARD - SUBMERGED PROP

22 cc - X460/3, X465, X665, 1465, 1662
DEEPVEE - INBOARD - SUBMERGED PROP

30 cc - 1470, 2167/3, X467, X470, X670, 1567
　
DEEPVEE - INBOARD - SURFACE PROP

3.5 cc - X445, X640, X642
DEEPVEE - INBOARD - SURFACE PROP

7.5 cc - X450/3, X452/3 X455, X457, X646/3
DEEPVEE - INBOARD - SURFACE PROP

11 cc - X457, X457/3, X460
DEEPVEE - INBOARD - SURFACE PROP

15 cc - X460/3, X462, X465, X665
DEEPVEE - INBOARD - SURFACE PROP

22 cc - X467, X470, 1567
DEEPVEE - INBOARD - SURFACE PROP

25 cc - X470, X472, X670, 1567
DEEPVEE - INBOARD - SURFACE PROP

30 cc - X472, X482, 1967
　
CATAMARAN - INBOARD - SUBMERGED PROP

3.5 cc - 1337/3, X438, X637
CATAMARAN - INBOARD - SUBMERGED PROP

7.5 cc - X447, X645, X646
CATAMARAN - INBOARD - SUBMERGED PROP

11 cc - 1455, 1650, X452, X455
CATAMARAN - INBOARD - SUBMERGED PROP

15 cc - 1457, 1460, 1860, X457, X460, X560
　
CATAMARAN - INBOARD - SURFACE PROP

3.5 cc - 1337/3, X438, X637
CATAMARAN - INBOARD - SURFACE PROP

7.5 cc - X447, X645, X646
CATAMARAN - INBOARD - SURFACE PROP

11 cc - 1455, 1650, X452, X455
CATAMARAN - INBOARD - SURFACE PROP

15 cc - 1457, 1460, 1860, X457, X460, X560
　
HYDRO / OUTRIGGER - INBOARD

3.5 cc - 1450, 1650, 1945, X447 X447/3, X448
HYDRO / OUTRIGGER - INBOARD

7.5 cc - 1455/3, 1457, 1457/3, 1745/3, 1950, 1950/3, 2.0/4, 2.1/3, X455, X455/3, X457
HYDRO / OUTRIGGER - INBOARD

11 cc - 1662, 1667, 1760, 1957, 2160, 2260, X462, X465
HYDRO / SCALE - INBOARD

11 cc - 1460, 1462, X457/3, X460, X560
HYDRO / OUTRIGGER - INBOARD

15 cc - 1470, 1667, 2167/3, 2267, X470, X670
　
HYDRO / OUTRIGGER - INBOARD - STRAIGHTAWAY

3.5 cc - 1750, 1950, 2047
HYDRO / OUTRIGGER - INBOARD - STRAIGHTAWAY

7.5 cc - 1760, 1957, 2160, 2260
HYDRO / OUTRIGGER - INBOARD - STRAIGHTAWAY

11 cc - 1860, 1967, 2160, 2167/3, 2260
HYDRO / OUTRIGGER - INBOARD - STRAIGHTAWAY

15 cc - 1967, 2167/3, 2267, 2.4/3
　
SPORT .40 - HYDRO

X447/3, X448, X450, X450/3, X452/3, X548, X646, X646/3, X648
　
TUNNEL - OUTBOARD

3.5 cc - X437/3, X438, X440, X440/3, X637, X640, 1640, 1938
TUNNEL - OUTBOARD

7.5 cc - X447, X447/3, X448, X646, 646/3, 648
TUNNEL - OUTBOARD

11 cc - X450, X450/3, X452, X452/3, 1450, 1650, 1950/3, 2150/3
TUNNEL - OUTBOARD - NEW

13.5 cc - X455, X455/3, X457, X457/3
　
OUTRIGGER - OUTBOARD

3.5 cc - 1740, 1740/3, 1742/3, 1.6/3
OUTRIGGER - OUTBOARD

7.5 cc - 1745/3, 1750, 2150/3, 2.0/4
OUTRIGGER - OUTBOARD

11 cc - 1752/3, 1755, 2.0/4, 2.1/3
　
THE FOLLOWING ARE SOME BASIC PROPELLER RECOMMENDATIONS FOR ELECTRIC BOATS. THE MAIN THING TO KEEP IN MIND WHEN SELECTING A PROP FOR YOUR ELECTRIC BOAT IS NOT TO OVER PROP. BIGGER IS NOT ALWAYS BETTER, PARTICULARLY ON AN ELECTRIC BOAT. IF YOU INSTALL TOO BIG A PROPELLER, THERE IS A GOOD CHANCE YOU WILL BURN UP YOUR MOTOR, SPEED CONTROL, ETC. THE BEST WAY !S TO START WITH THE SMALLEST PROPELLER RECOMMENDED, PUT THE BOAT OUT FOR A SHORT (20 - 30 SECONDS) RUN, BRING IT BACK IN AND FEEL THE MOTOR(S). IF YOU CAN HOLD ONTO THE MOTOR - NO PROBLEM, IF COOL YOU MAY BE ABLE TO INCREASE YOUR PROP SIZE. IF YOU CAN NOT HOLD ONTO THE MOTOR(S) YOU HAVE TOO BIG A PROP FOR YOUR BOAT/MOTOR/CELL COMBINATION AND YOU WOULD BE ADVISED TO TRY A SMALLER PROPELLER.
　
THE FOLLOWING BASIC GUIDELINES ARE FOR SURFACING APPLICATIONS UNLESS OTHERWISE NOTED.
　
DIRECT DRIVE - SINGLE MOTOR (not less than 20 winds) - MAXIMUM 8 CELLS
HYDRO X427, X430, X432, X435
OUTRIGGER 1732, 1735
MONO (submerged) 0930, X427, X430
　
GEARED 2 : 1 - MAXIMUM 12 CELLS
SINGLE MOTOR - HYDRO X438, X440, X637, X640
TWIN MOTORS - HYDRO X447, X447/3, X645, X646, X646/3
SINGLE MOTOR - OUTRIGGER 1740, 1740/3, 2137/3
TWIN MOTORS - OUTRIGGER 1745/3, 1750, 2047, 2150/3


A.C.
Autor:  adamM [ 25 lut 2012, 19:05 ]
Tytuł:  Re: Śruby Ściągawka jak dobierać Sruby OCTURA
ale Andrzeju nie dodałęś że jak jeden model smiga na danej śrubie to drugi "taki sam" wcale śmigać nie musi :P
Autor:  adam [ 25 lut 2012, 20:21 ]
Tytuł:  Re: Śruby Ściągawka jak dobierać Sruby OCTURA
adamM napisał(a):
ale Andrzeju nie dodałęś że jak jeden model smiga na danej śrubie to drugi "taki sam" wcale śmigać nie musi :P

Adam,
jest jedno pewne, że model bez śruby nie będzie śmigał :chinczyk:

Meniu
Strona 1 z 1 Strefa czasowa: UTC + 1 [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/